Saab 93 Key Fob Replacement
Saab key fobs with 93 keys can be expensive to replace. However the process is simple.
You'll require a phillips screwdriver with a flat head and a little patience. Place the screwdriver in the middle of the case and slowly lift it.
It is an excellent idea to keep spare fobs and keys. They could save you from getting stranded or having to pay towing charges.
How to replace the battery
Car key fobs that allow and lock the vehicle remotely contain batteries inside that will eventually fail. When that occurs owners can replace the battery of their key fob themselves in a few easy steps. The key fob comes with two plastic flaps on the one side that you must open in order to take out the battery and replace it with an alternative one. The CR1632 battery that is standard in size can be used as a replacement. It is simple to install.
After removing the emergency key, you can apply the flathead screwdriver to a small piece of wood to break the case. Do not press the case too hard as the electronics are delicate and could be damaged by excessive pressure.
Saab produced some amazing automobiles. Many of them are still around today. One of the major issues with these cars, however, is the ignition keys. The buttons can become stuck or lose their function as time passes. It can be costly for a Saab owner to purchase a new key at the dealer in the event they lose their primary functioning one. They'll need to replace the computer module and then program the new key in order to convince the car that you're not attempting to steal it. You can save money by replacing the case.
How to remove the manual key?
Batteries are present in all key fobs used to lock and unlock cars. These batteries are of a limited duration. If saab 9-3 key programming 're like most people they will go out at some time. It's easy to replace the battery for the key fob that is manual. The only thing that is difficult is removing the old battery from the case, but it's nothing a little patience and a little bit of effort using a flathead screwdriver will not help you with.
Once you have the new battery installed, it's time to put everything back together. To accomplish this, you'll need open up the replacement key fob's case. This can be done by inserting a flathead screwdriver into the slot located in the middle of the case. Work the case gently until it splits in two and you can remove it from the key fob.
You may have to reprogram the new key fob in case the previous key fob has lost its connection to the security system of your car. You can do this by following the manual learning process to create a new FOB for your Saab 9-5. This method is not a way to invalidate previously learned keys and you are able to use the existing FOBs in case they need to be programmed again. This process is only initiated by ensuring that the mechanical key of the vehicle matches the cut on the FOB.
How to Change the Case
If you're replacing the battery or the manual key it's a good idea replace the case too. The cases are susceptible to wear out, particularly after a lot of use. It's easy to replace the case of your SAAB 9-3 and you don't require any special tools.
The first step in changing the case is to remove the manual key from the fob. This can be done by pressing the SAAB logo and then pulling out the manual key. The fob for the key may be sticky at times, and it may take a little amount of force to pull the key out.
Once you've removed the manual key from the case, you can begin to remove the electronic components. You'll need a flathead screwdriver for this. Be gentle with your screwdriver so as not to harm any electronics. After you've removed all the electronic components, you'll need take the battery out. Once you've replaced the battery, you'll be able to put everything back together in an entirely new case. You can purchase cases for replacement on the internet at a fairly low cost.
How to program the new key
All key fobs that permit you to lock and unlock your car remotely have batteries, but they only last for a certain time. It is important to remember this and change the battery in your key fob at least every three or four years. Fortunately it is a simple process that can be accomplished at home. All you need is a little patience and the smallest screwdriver, a flathead.
The first step is to remove the manual key. Press the blue SAAB logo and then pull the emergency key from the key fob. It may require some force but the key should be released easily. Once you have the key fob open then you can remove the old battery by gently pushing the screwdriver into the slot located in the middle of the case. This will split the case and make it easier to get at the electronics.
It is now time to program the key. This can be done by following the steps outlined in this video by YouTube user Cyclone Cyd. Cyclone Cyd's channel on YouTube provides excellent tips on how to do simple maintenance and repairs on cars.
Key fobs are an excellent way to have an extra key for your car in the event you lose one or break it. You can buy a new key fob online or at an authorised locksmith in your area, such as United Locksmith. The cost is much cheaper than at a dealership, which will charge you for the key and programming it into the car.